10.11 PtEncoderChannelSignalTypeVariableType
The PtEncoderChannelSignalTypeVariableType is a subtype of the 0:MultiStateValueDiscreteType. It is used to encode the signal type of the encoder channel. It is formally defined in Table 86.
| Attribute | Value | ||||||
| BrowseName | PtEncoderChannelSignalTypeVariableType | ||||||
| IsAbstract | False | ||||||
| ValueRank | -1 (-1 = Scalar) | ||||||
| DataType | 0:UInt16 | ||||||
| References | NodeClass | BrowseName | DataType | TypeDefinition | Other | ||
|---|---|---|---|---|---|---|---|
| Subtype of the 0:MultiStateValueDiscreteType defined in OPC 10000-8. | |||||||
| HasProperty | Variable | EnumValues | EnumValueType[] | PropertyType | M | ||
| Conformance Units | |||||||
|---|---|---|---|---|---|---|---|
| Powertrain Encoder Channel |
| BrowsePath | Value Attribute |
| 0:EnumValues | [ { "Value":0, "DisplayName": "OTHER", "Description": "Other encoder protocol" }, { "Value":1, "DisplayName": "BISS_C", "Description": "BiSS interface continuous mode" }, { "Value":2, "DisplayName": "ENDAT2.1", "Description": "EnDat (Encoder Data), operating mode 2.1" }, { "Value":3, "DisplayName": "ENDAT2.2", "Description": "EnDat (Encoder Data), operating mode 2.2" }, { "Value":4, "DisplayName": "HIPERFACE", "Description": "Hiperface" }, { "Value":5, "DisplayName": "HIPERFACE_DSL", "Description": "Hiperface DSL (Digital Servo Link)" }, { "Value":6, "DisplayName": "SSI_BINARY", "Description": "Binary synchronous serial output (SSI)" }, { "Value":7, "DisplayName": "SSI_GRAY_CODE", "Description": "Gray code synchronous serial output (SSI)" }, { "Value":8, "DisplayName": "SINCOS_1VSS", "Description": "SinCos, 1 Vss output level" }, { "Value":9, "DisplayName": "SCS_OPEN_LINK", "Description": "Single cable solution (SCS open link)" }, { "Value":10, "DisplayName": "DRIVECLIQ", "Description": "DRIVE-CLiQ" }, { "Value":11, "DisplayName": "BISS_LINE", "Description": "BiSS Line" }, { "Value":12, "DisplayName": "FANUC_37BIT_SERIAL_COMM", "Description": "Fanuc 37-bit serial interface" }, { "Value":13, "DisplayName": "MITSUBISHI_40BIT_SERIAL_COMM", "Description": "Mitsubishi 40-bit serial interface" }, { "Value":14, "DisplayName": "OMRON/PANASONIC_48BIT_SERIAL_COMM", "Description": "OMRON/Panasonic 48-bit serial interface" }, { "Value":15, "DisplayName": "YASKAWA_36BIT_SERIAL_COMM", "Description": "Yaskawa 36-bit serial interface" }, { "Value":16, "DisplayName": "RS422_5V_TTL", "Description": "RS422 (TTL - Transistor Transistor Logic), 5 V signal level" }, { "Value":17, "DisplayName": "RS422_5..30V", "Description": "RS422 signal level depend on entry level 5 V to 30 V" }, { "Value":18, "DisplayName": "SINCOS_1VPP", "Description": "SinCos, 1 Vss output level" }, { "Value":19, "DisplayName": "RESOLVER", "Description": "Resolver signal" }, { "Value":20, "DisplayName": "HTL_PUSH-PULL", "Description": "High Threshold Logic (HTL), typically voltage ranges from 5 to 30 VDC" }, { "Value":21, "DisplayName": "RS485", "Description": "RS-485, signal is transmitted over a Sig+ line and a Sig- line" }, { "Value":22, "DisplayName": "RS485_SINCOS", "Description": "RS-485, Sin-/Cos-Signal" }, { "Value":23, "DisplayName": "RS485_HTL", "Description": "RS-485, High Threshold Logic (HTL) signal" }, { "Value":24, "DisplayName": "RS485_TTL", "Description": "RS-485, Transistor Transistor Logic (TTL) signal" } ] |
The predefined attribute values must be supported by the Server for each instance. Future versions of this specification might extend the value range.