Search

88 result(s) for Components

• OPC-10000-82 – OPC Unified Architecture - Part 82: UAFX Networking
  1 Scope
  Ethernet networks. Future releases will add additional requirements, including additional definitions for End Station Components and NETCONF-based remote management. Definitions for additional physical layer protocols such as SPE/APL, WLAN ... these networks. UAFX intends for all networking-related configuration of End Station and Bridge Components to be done through NETCONF. Towards this goal, this release selects the basic protocol layers
• OPC-10000-82 – OPC Unified Architecture - Part 82: UAFX Networking
  3.1.9 IA-station
  station material element or assembly composed of one or more End Station Components and zero or more Bridge Components
• OPC-10000-82 – OPC Unified Architecture - Part 82: UAFX Networking
  6.4.1 Overview
  include a Bridge Component (see 6.2 ). More complex IA-stations incorporating several End Station Components and Bridge Components within one device can also be found in industrial automation ... source or destination for data traffic. These functions, located in the End Station Components , include industrial automation applications, Remote Management , and other applications or services such as Time Synchronisation
• OPC-10000-82 – OPC Unified Architecture - Part 82: UAFX Networking
  6.4.2 IA-station requirements
  defined in clause 7.3 . An IA-station may: comprise one or more conformant Bridge Components as defined in 6.2 , support remote management as defined in clause 7.2 , support time synchronisation
• OPC-10000-82 – OPC Unified Architecture - Part 82: UAFX Networking
  7.2.2 NETCONF
  modules to be supported by a UAFX Station . A single management entity controls all components of a UAFX Station. Figure 16 shows a UAFX Station comprised of two End Station ... Components and one Bridge Component , all controlled by a single management entity. Figure 16 - Example of a UAFX Station supporting NETCONF NETCONF messages are recommended to be transmitted using priority
• OPC-10000-82 – OPC Unified Architecture - Part 82: UAFX Networking
  7.3.2.2.4.4 System Capabilities TLV
  System Capabilities TLV A UAFX Station consisting of only one or more End Station Components shall set the system and enabled capabilities fields to Station Only ... that the internal structure of the UAFX Station consists of multiple components. This is a deliberate deviation from a footnote in IEEE Std 802.1AB‑2016 , Table
• OPC-10000-84 – OPC Unified Architecture - Part 84: UAFX Profiles
  5.2.6 UAFX ConnectionManager
  ConnectionManagerType . This includes support of ConnectionConfigurationSetType instances, including any subtypes of ConnectionConfigurationSetType Components that are supported. Server UAFX ConnectionManager ConnectionsDiagnostics Supports the ConnectionsDiagnostics Variable of the ConnectionConfigurationSetType . Server UAFX ConnectionManager
• OPC-30210-1 – OPC UA for Unattended Retail & Coffee Solutions - Part 1: Core Components
  7.1.2 ObjectType definition
  HasComponent Object Delivery MachineEngineDeliveryType M 0:HasComponent Object Status MachineEngineStatusType M 0:HasComponent Object Components BaseComponentsType O 0:GeneratesEvent ObjectType VendingBaseAuditEventType 0:GeneratesEvent ObjectType ConfigurationChangedEventType Conformance Units UnattendedRetail MachineEngine ... consumed by the payment service (see 7.7 for details). The optional Components Object is the entry point to information about subcomponents of the machine engine (see 7.4 for details
• OPC-30210-1 – OPC UA for Unattended Retail & Coffee Solutions - Part 1: Core Components
  7.8.2 ObjectType definition
  HasComponent Object PaymentDevices PaymentDevicesType O 0:HasComponent Object Status PaymentServiceStatusType M 0:HasComponent Object Components BaseComponentsType O 0:GeneratesEvent ObjectType VendingAuditEventType 0:GeneratesEvent ObjectType ConfigurationChangedEventType Conformance Units UnattendedRetail PaymentService ... service and thereby of the overall Vending Machine (see 7.22 for details). The optional Components Object is the entry point to information about subcomponents of the payment service
• OPC-30210-1 – OPC UA for Unattended Retail & Coffee Solutions - Part 1: Core Components
  7.17.2 ObjectType definition
  Other Subtype of the PaymentDeviceType 0:HasComponent Object Configuration BaseConfigurationType M 0:HasComponent Object Components BaseComponentsType O 0:GeneratesEvent ObjectType ConfigurationChangedEventType Conformance Units UnattendedRetail PaymentDevice Coin UnattendedRetail PaymentDevice Bill UnattendedRetail ... details). It may provide the default currency used in the payment device. The optional Components Object is the entry point to information about subcomponents of the payment device
• OPC-30210-1 – OPC UA for Unattended Retail & Coffee Solutions - Part 1: Core Components
  7.23.2 ObjectType definition
  Object 2:Identification IdentificationType M 0:HasComponent Object Configuration BaseConfigurationType M 0:HasComponent Object Components BaseComponentsType O 0:GeneratesEvent ObjectType VendingBaseAuditEventType 0:GeneratesEvent ObjectType ConfigurationChangedEventType Conformance Units UnattendedRetail ... Object provides the configuration information of the UI (see 7.3 for details). The optional Components Object is the entry point to information about subcomponents
• OPC-30210-1 – OPC UA for Unattended Retail & Coffee Solutions - Part 1: Core Components
  7.24.2 ObjectType definition
  HasComponent Object Configuration BaseConfigurationType M 0:HasComponent Object PriceInformation PriceInformationType M 0:HasComponent Object Components BaseComponentsType O 0:GeneratesEvent ObjectType ConfigurationChangedEventType Conformance Units UnattendedRetail PriceService The 2: Identification Object provides ... machine engines, managed by the payment service (see 7.11 for details). The optional Components Object is the entry point to information about subcomponents of the machine engine
• OPC-30210-1 – OPC UA for Unattended Retail & Coffee Solutions - Part 1: Core Components
  7.25.2 ObjectType definition
  BaseConfigurationType M 0:HasComponent Variable IsCollectingAudit 0:Boolean 0:BaseDataVariableType M 0:HasComponent Object Components BaseComponentsType O 0:GeneratesEvent ObjectType ConfigurationChangedEventType Conformance Units UnattendedRetail AuditCollect The 2: Identification Object provides ... supervise this Variable and reject requests if audit is not running. The optional Components Object is the entry point to information about subcomponents of the audit collect
• OPC-30500-1 – OPC UA for Laboratory & Analytical Device Standard (LADS) - Part 1: Basics
  5.2.1 Device and fleet management
  recognized correctly in the server. Furthermore, a Device is composed of different Components . Each of these  Components can have a nameplate itself. The definition of Components
• OPC-30500-1 – OPC UA for Laboratory & Analytical Device Standard (LADS) - Part 1: Basics
  7.1.1 LADSDeviceType ObjectType Definition
  Other Subtype of the DeviceType defined in OPC 10000-100 0:HasAddIn Object 4:Components LADSComponentsType O 0:HasComponent Object FunctionalUnitSet FunctionalUnitSetType M 0:HasProperty Variable 3:HierarchicalLocation 0:String ... MachineryOperationCounterType O 0:HasAddIn Object 4:LifetimeCounters 4:MachineryLifetimeCounterType O Conformance Units LADS LADSDeviceType Components is a generic set of identifiable sub-components of the Device as mandated
• OPC-30500-1 – OPC UA for Laboratory & Analytical Device Standard (LADS) - Part 1: Basics
  7.1.2.1 Overview
  represent a PowerSave state where a Device may shut down some of its Components , such as the GUI. It can also be used to represent a Sleep state, where
• OPC-30500-1 – OPC UA for Laboratory & Analytical Device Standard (LADS) - Part 1: Basics
  7.1.3 LADSComponentType ObjectType Definition
  Other Subtype of the 2:ComponentType defined in OPC 10000-100 0:HasAddIn Object Components LADSComponentsType O 0:HasAddIn Object 2:Identification M 0:HasComponent Object Maintenance MaintenanceSetType ... BaseDataVariableType O 0:HasComponent Object 2:DeviceHealthAlarms 0:FolderType O Conformance Units LADS LADSComponentType Components is a generic set of identifiable subcomponents of the device as mandated
• OPC-40001-2 – OPC UA for Machinery - Part 2: Process Values
  6.5 Examples applying Process Values
  this specification. The X: MyMachine Object contains a X: Sensor1 in its 4: Components folder. The X: Sensor1 provides identification information and health status. In addition, it contains two process
• OPC-40010-1 – OPC UA for Robotics - Part 1: Vertical Integration
  7.18.2 ControllerType definition
  String 0:PropertyType M 0:HasComponent Object CurrentUser   UserType M 0:HasComponent Object Components   0:FolderType O 0:HasComponent Object Software   0:FolderType M 0:HasComponent Object TaskControls   0:FolderType ... Base Table 96 - ControllerType Additional Subcomponents Source Path Reference NodeClass BrowseName DataType TypeDefinition Others Components 0:HasComponent Object <ComponentIdentifier> 2:ComponentType MP Software 0:HasComponent Object <SoftwareIdentifier
• OPC-40082-4 – OPC UA interfaces for plastics and rubber machinery - Peripheral devices - Part 4: Dosing Systems
  8.13 Components
  Components This ObjectType is a container for all Components in the DosingSystem . The ComponentsType is described in chapter
• OPC-40082-4 – OPC UA interfaces for plastics and rubber machinery - Peripheral devices - Part 4: Dosing Systems
  11.20.1 ContinuousComponentType definition
  ContinuousComponentType definitionThe ContinuousComponentType is a subtype of the abstract ComponentType and describes Components , where the materials are fed to the production machine in a continuous flow instead of batches
• OPC-40082-4 – OPC UA interfaces for plastics and rubber machinery - Peripheral devices - Part 4: Dosing Systems
  11.21.1 BatchComponentType definition
  BatchComponentType definitionThe BatchComponentType is a subtype of the abstract ComponentType and describes Components , where the materials are fed to the production machine in batches e.g. prepared by a batch
• OPC-40083 – OPC UA for Plastics and Rubber Machinery - General Type Definitions
  20.3.5 Load
  activated can be chosen. Signature Load ( [in] 0:String Name [in] 0:UInt16[] Components); Table 104 - Load Method Arguments Argument Description Name Name of the production dataset that should ... loaded. Components Indication which parts of the production dataset shall be activated. See Table 115 for possible values If Components is not given (array length 0) then the complete Production
• OPC-40083 – OPC UA for Plastics and Rubber Machinery - General Type Definitions
  20.5.3 GenerateOptions in GenerateFileForWrite
  production dataset that should be transferred from the client to the server. Components 0:UInt16[] Array which indicates which parts of the production dataset shall be activated in the machine ... PREPARATION_2. Array of UInt16. See possible values in Table 115 . If Components has the array length 0 then complete production dataset is activated. Table 118 - StorageEnumeration Definition Name Value
• OPC-40083 – OPC UA for Plastics and Rubber Machinery - General Type Definitions
  20.6 Events for ProductionDatasetTransfer
  PropertyType M 0:HasProperty Variable Name 0:String 0:PropertyType M 0:HasProperty Variable Components 0:UInt16[] 0:PropertyType M Name : Name of the production dataset that should be transferred ... from the client to the server. Storage : Indication where the dataset is written to. Components : Array which indicates which parts of the production dataset shall be activated in the machine
• OPC-40100-2 – OPC UA for Machine Vision - Part 2: Asset Management and Condition Monitoring
  8.1 VisionSystemAssetType ObjectType Definition
  inheriting the InstanceDeclarations of that Node 0:HasAddIn Object 3:Components 3:MachineComponentsType O 0:HasComponent Object ComputingDevices VisionItemFolderType O 0:HasComponent Object DisplayUnits VisionItemFolderType O 0:HasComponent Object PhysicalInterfaces ... Health VisionHealthInfoType O Conformance Units VSA_BasicIdentification VSA_ExtendedIdentification VSA_MaintenanceInformation VSA_HealthInformation The Components object (with a standardized BrowseName as defined in the OPC UA for Machinery companion specification
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  3.2.1 Airnet
  Airnet Piping and all Components between at least two distinct points, the inputs and outputs of the Airnet , in a Compressed Air System . Note 1 to entry: A Component
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  3.2.2 CASPart
  System . Note 1 to entry: CASParts defined in this specification are: Airnet , all Components , Main Control System
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  3.2.4 Compressed Air System
  Compressed Air System System that generates compressed air, consists of Components and at least one Airnet , and is commonly equipped with one Main Control System
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  3.2.12 Main Control System
  Main Control System CASPart that controls all Components and Airnets simultaneously, represents the Compressed Air System , and serves for communication between the Components and higher-level systems
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  3.2.13 Main Function [of a Component]
  Main Function [of a Component] The actual main function of Components is not specified in this specification. The following examples of Main Functions do not imply the actual function
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  5.1 Device Identification
  should be able to explore the topology of the Compressed Air System . All browsable Components shall be identifiable. This includes non-communicating Components (e.g. Airnet , receiver) as well as assets
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  5.3 Maintenance Management
  Maintenance Management For the integration of Compressed Air System Components in an operator's maintenance management application, the Main Control System should provide Compressed Air System specific maintenance properties
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  6.4 Identification
  Properties . The Main Control System is identified by an Identification Object of the MachineryComponentIdentificationType. Components are identified by an Identification Object of a subtype of the abstract MachineryItemIdentificationType defined ... Component , the Identification Object must use an appropriate subtype of the MachineryItemIdentificationType. For all Components and the Main Control System the DeviceClass Property has its Value Attribute
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  6.7 Adding new Components
  Adding new Components All Component ObjectTypes in this specification (clauses 7.8 - 7.19 ) may be used for subtyping when defining more specific Components . If future companion specifications, a manufacturer, or system ... integrator wants to define a more specific ObjectType for one of the existing Components , the ObjectType of that Component shall be used as supertype. If future companion specifications, a manufacturer
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  7.1 CASType ObjectType Definition
  Compressed Air System and provides both Objects for Quantities and FunctionalGroups for its Airnets , Components , and the Main Control System . It is illustrated in Figure 16 and formally defined ... HasComponent Object Airnets AirnetsType O 0:HasComponent Object 4:Components ComponentsGroupType O 0:HasComponent Object 2:Identification CASIdentificationType O 0:HasComponent Object MCS MCSType O The CASType ObjectType
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  7.3 ComponentsGroupType ObjectType Definition
  ComponentsGroupType ObjectType Definition The ComponentsGroupType enables the grouping of Components and can be nested. It is illustrated in Figure 18 and formally defined in Table 15 . Figure 18 - ComponentsGroupType Illustration ... OptionalPlaceholder Object <ComponentsGroup> allows nesting this ObjectType to further categorize the referenced Components . It also allows adding concrete Component groups not defined by this specification. The InstanceDeclarations
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  7.4 AirnetType ObjectType Definition
  InstanceDeclarations of that Node. 0:HasComponent Object Ambient FluidQuantitiesType O 0:HasComponent Object 4:Components AirnetComponentsType O 0:HasComponent Object 2:Configuration AirnetConfigurationType O 0:HasComponent Object ElectricalCircuit ElectricalCircuitType ... FluidQuantitiesType only AbsolutePressure, DewPoint, RelativeHumidity, and Temperature are available. The optional Folder Components provides Folders for organizing Components connected to the Airnet . Usually, the Components are grouped by their DeviceClass
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  7.29 ConfigurationType ObjectType Definition
  Airnets and the Main Control System . There are no configuration properties defined for Components . It is formally defined in Table 61 . Table 61 - ConfigurationType Definition Attribute Value BrowseName ConfigurationType IsAbstract
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  7.33 DesignType ObjectType Definition
  ObjectType Definition The DesignType provides a framework and Variables for static design information of Components and is formally defined in Table 70 . Table 70 - DesignType Definition Attribute Value BrowseName DesignType
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  7.43 EventsType ObjectType Definition
  EventsType ObjectType DefinitionThe EventsType provides Objects for conditions of Components and is formally defined in Table 90 . Table 90 - EventsType Definition Attribute Value BrowseName EventsType IsAbstract False References Node
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  7.45 OperationalType ObjectType Definition
  Enumeration 0:DataItemType O, RO The optional Variable HealthState is used for Airnets and Components and describes whether the Main Function of a Component or the Requirements of an Airnet ... specific definition of this Variable . The optional Variable IntegratedState is used for Airnets and Components and describes the degree of control over compressed air generation and/or treatment. Some subtypes
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  7.46 AirnetOperationalType ObjectType Definition
  Definition Property . For the description it is important to define system boundaries and which Components of an Airnet are included in the calculation. The EngineeringUnits Property shall be used
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  9.2.2.4 CAS Base Configuration Server Facet
  Control System that provides its OPC UA communication settings and the component class for Components . Table 166 - CAS Base Configuration Server Facet Group Conformance Unit / Profile Title
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  B.1 Adding or Removing a Component to/from a Compressed Air System
  System , the manufacturer, integrator, or operator may wish to replace, add, or remove Components to or from the system. The OPC UA provided Services AddNodes and DeleteNodes ... Compressed Air System wants to enable an integrator or operator to add or remove Components while the OPC UA Server is running, at least those two Services shall be available
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  B.2 Adding or Removing a Component to/from an Airnet
  Compressed Air System the manufacturer, integrator, or operator may wish to add or remove Components to or from one of the Airnets . This also includes moving a Component permanently from ... Compressed Air System wants to enable an integrator or operator to add or remove Components to or from one of the Airnets , or to move Components from one Airnet
• OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems
  B.3 Temporarily Switch a Component from one Airnet to Another
  Switch a Component from one Airnet to Another Some Main Control Systems allow for Components to switch from one Airnet to another by operating a valve or a similar action ... setup of a Compressed Air System allows for such a temporarily switch, the switchable Components shall have the ActiveAirnet Property and all possible Airnets shall have an Organizes Reference
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  1 Scope
  their attributes (catalogue data). By use of specific references, the relationship of asset components can be represented. Future parts will address the following topics: Functional operation data Information about
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  3.2 OPC UA for Powertrain terms
  Separately orderable hardware for power supply (e.g., 24V DC) for the electronics of the components of a power drive system (PDS) . Naming according to IEC 61800-2 Axis Logical element ... type of circuit that serves as a common pathway shared by several components , and which uses a direct current voltage level as a reference. DC bus module Separately orderable component
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  3.4.1.1 Node definitions
  this document points to their definition. Table 3 illustrates the table. If no components are provided, the DataType, TypeDefinition and ModellingRule columns may be omitted and only a Comment column ... such as the ModellingRule or AccessLevel . NOTE Notes referencing footnotes of the table content. Components of Nodes can be complex that is containing components by themselves. The TypeDefinition , NodeClass
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  3.4.1.2 Additional References
  information about additional References , the format as shown in Table 5 is used. The components of the ObjectType have additional references which are defined in Table 5 . Table
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  3.4.1.3 Additional sub-components
  Additional sub-components To provide information about sub- components , the format as shown in Table 6 is used. Table 6 - <some>Type Additional Subcomponents BrowsePath Reference NodeClass BrowseName
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  4.1 Introduction to Powertrain
  Introduction to Powertrain Powertrain stands for a system that includes electromechanical components e.g. one or more motor starter(s), complete drive module(s) (CDM) , electric motor(s) as well
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  5 Use cases
  many ways. Also, for Industrie 4.0 applications and processes, too, electrical and mechanical drive components , as data source and as an active part of intelligent applications, are an essential building ... block. In mechanical and plant engineering, a wide variety of drive components from a wide range of manufacturers are used, each of which must be integrated into comprehensive, complex systems
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  6.1 Powertrain
  component related products (e.g., motor, gearmotor, encoder, sensors). Out of scope are mains and components of the load side. Figure 9 - Scope of the Information Model
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  6.2 Information Model Structure
  encoder and brake. These entities are called assets ( PtAssetType ) and have one or more components holding their asset attributes ( PtAssetAttributesType ). Also, it´s possible to model a software asset type ... asset's attributes. The most common attributes of asset types are added as mandatory components . e. g. motor and encoder for servo motor. 2. PtAssetAttributesType ( powertrain asset attribute type) Asset
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  7.4.17.1 Overview
  charge is to limit initial charging (inrush) currents to levels that all components can withstand. The PtAssetPrechargeType is formally defined in Table 53 . The PtAssetPrechargeType is a subtype
• OPC-40400-1 – OPC UA for the Powertrain - Part 1: Asset Management
  7.9.2.2 Object Description
  range in which the asset can operate/is designed for. Min/Max voltage that electrical components can handle. The unit shall be volt [V]. The attributes of the PtDcBusAttributesType have additional
• OPC-40501-1 – OPC UA for Machine Tools - Part 1: Machine Monitoring and Job Management
  9.2 InterruptionConditionType
  tool manually. To indicate the reason for the process to be interrupted, the Components 0:ConditionClassId and 0:ConditionClassName of the InterruptionConditionType shall indicate the most appropriate ConditionClass . This specification
• OPC-40501-1 – OPC UA for Machine Tools - Part 1: Machine Monitoring and Job Management
  9.4 ProductionJobTransitionEventType
  ProductionJobStateMachineType is triggered. It purposely contains a consistent snapshot of the properties and components of the ProductionJobType in order to transport the information valid in the state reached ... IsDeprecated Object MachineTool_v102 0:BaseObjectType Conformance Units MachineTool Production ProductionJobStateMachineType All Properties and Components in Table 86 are described in 8.4.3 for the ProductionJobType . Their values in the ProductionJobTransitionEventType
• OPC-40501-1 – OPC UA for Machine Tools - Part 1: Machine Monitoring and Job Management
  9.5 ProductionPartTransitionEventType
  ProductionPartStateMachineType is triggered. It purposely contains a consistent snapshot of the properties and components of the ProductionPartType in order to transport the information valid in the state reached ... Identifier property of the ProductionJobType instance this part belongs to. All other Properties and Components in Table 88 are described in 8.4.7 for the ProductionPartType . Their values in the ProductionPartTransitionEventType
• OPC-40560 – OPC UA for Mining - General
  7.2.3 ObjectType Description
  ObjectType Description The Components Object of type MachineComponentsType is an AddIn-Feature, allowing a structured way to represent hierarchies of machine components. It is usually populated at the time
• OPC-40564-2 – OPC UA for Mining - Mineral Processing - Part 2: Rock Crusher
  7.1.3 ObjectType description
  descriptions of other inherited instance declarations. Specifically, the Components and MiningEquipmentIdentification instance declarations of the RockCrusherType are defined
• OPC-40570 – OPC UA for Wire Harness Manufacturing
  10.4.2 ObjectType definition
  Identification WireHarnessMachineIdentificationType Mandatory HasComponent Object 4:MachineryBuildingBlocks 0:FolderType Mandatory HasAddIn Object 4:Components 4:MachineComponentsType Optional Conformance Units WireHarness WireHarnessMachineType 4:Identification provides properties to identify a Device ... Components contains the details of all components of the machine. See OPC 40001-1 for more information. PartManagement contains the part list and the method to manage this list. ArticleSpecManagement
• OPC-40700 – OPC UA for Surface Technology - General Types
  6 Surface Technology General Types Information Model overview
  model more complex plants and systems. In some cases, these systems can contain different components. The STCompType was developed to map these in detail. Instances of components must be located ... within the Components Object of the corresponding system. In the example shown, MyComponent (these are the blue Nodes ) represents such an exemplary component of the system MySystem1 . The STBaseControllerType , which
• OPC-40700 – OPC UA for Surface Technology - General Types
  7.1 STSysType ObjectType Definition
  HasAddIn Object 2:Identification 4:MachineIdentificationType O 0:HasAddIn Object 4:Components 4:MachineComponentsType O 0:HasComponent Object 4:Monitoring 4:MonitoringType O 0:HasComponent Object 4:MachineryBuildingBlocks 0:FolderType ... defined in OPC 40001-1. It represents numerous identification features of the system. Components is representing a collection of all physical components of the Surface Technology System. Monitoring is representing
• OPC-40701 – OPC UA for Surface Technology - Cleaning and Pretreatment
  6 Cleaning and Pretreatment Machinery Information Model overview
  General Types ( STGeneral ), which is structured to represent the physical machine and its system components in a modular way. This is necessary due to the complex and varied nature ... machine in accordance with OPC UA for Machinery and can contain additional components of 3:MachineComponentsType , which serve to model the structure and location of sensors in single systems
• OPC-40701 – OPC UA for Surface Technology - Cleaning and Pretreatment
  7.1 STSysAuxiliaryType ObjectType Definition
  HasComponent Object 3:Monitoring 3:MonitoringType O 0:HasAddIn Object 3:Components 3:MachineComponentsType O Conformance Units STCleaningPretreatment STSysAuxiliaryType Basic STCleaningPretreatment STSysAuxiliaryType Identification STCleaningPretreatment STSysAuxiliaryType Advanced Monitoring represents a collection ... variables that are not assigned to a component but to the overall system. Components is an add-in used to assign components (e.g. of STCompType ) to the system. The components
• OPC-40701 – OPC UA for Surface Technology - Cleaning and Pretreatment
  7.2 STSysCleaningType ObjectType Definition
  Other Subtype of the 9:STSysType defined in OPC 40700 0:HasAddIn Object 3:Components 3:MachineComponentsType O Conformance Units STCleaningPretreatment STSysCleaningType Basic STCleaningPretreatment STSysCleaningType Identification STCleaningPretreatment STSysCleaningType Advanced Components ... used to assign components (e.g. of STCompType ) to the system. The components of the STSysCleaningType have additional subcomponents which are defined in Table 18 . Table 18 - STSysCleaningType Additional Subcomponents Source
• OPC-40701 – OPC UA for Surface Technology - Cleaning and Pretreatment
  7.3 STSysConveyorType ObjectType Definition
  HasComponent Object 3:Monitoring 3:MonitoringType O 0:HasAddIn Object 3:Components 3:MachineComponentsType O Conformance Units STCleaningPretreatment STSysConveyorType Basic STCleaningPretreatment STSysConveyorType Identification STCleaningPretreatment STSysConveyorType Advanced Monitoring represents a collection ... variables that are not assigned to a component but to the overall system. Components is an add-in used to assign components (e.g. of STCompType ) to the system. The components
• OPC-40701 – OPC UA for Surface Technology - Cleaning and Pretreatment
  7.4 STSysDryingType ObjectType Definition
  HasComponent Object 3:Monitoring 3:MonitoringType O 0:HasAddIn Object 3:Components 3:MachineComponentsType O Conformance Units STCleaningPretreatment STSysDryingType Basic STCleaningPretreatment STSysDryingType Identification STCleaningPretreatment STSysDryingType Advanced Monitoring represents a collection ... variables that are not assigned to a component but to the overall system. Components is an add-in used to assign components (e.g. of STCompType ) to the system. The components
• OPC-40701 – OPC UA for Surface Technology - Cleaning and Pretreatment
  7.5 STSysHandlingType ObjectType Definition
  HasComponent Object 3:Monitoring 3:MonitoringType O 0:HasAddIn Object 3:Components 3:MachineComponentsType O Conformance Units STCleaningPretreatment STSysHandlingType Basic STCleaningPretreatment STSysHandlingType Identification STCleaningPretreatment STSysHandlingType Advanced Components ... used to assign components (e.g. of STCompType ) to the system. The components of the STSysHandlingType have additional subcomponents which are defined in Table 24 . Table 24 - STSysHandlingType Additional Subcomponents Source
• OPC-40701 – OPC UA for Surface Technology - Cleaning and Pretreatment
  7.6 STSysMaterialSupplyType ObjectType Definition
  Other Subtype of the 9:STSysType defined in OPC 40700 0:HasAddIn Object 3:Components 3:MachineComponentsType O Conformance Units STCleaningPretreatment STSysMaterialSupplyType Basic STCleaningPretreatment STSysMaterialSupplyType Identification STCleaningPretreatment STSysMaterialSupplyType Advanced Components ... used to assign components (e.g. of STCompType ) to the system. The components of the STSysMaterialSupplyType have additional subcomponents which are defined in Table 26 . Table 26 - STSysMaterialSupplyType Additional Subcomponents Source
• OPC-40701 – OPC UA for Surface Technology - Cleaning and Pretreatment
  7.7 STSysQualityControlType ObjectType Definition
  variables that are not assigned to a component but to the overall system. Components is an add-in used to assign components (e.g. of STCompType ) to the system. The components ... units). QualityIndexPart represents the calculated Index Score of the quality-determining parameters of the components. Suggested unit: -. ParticleWeightPart describes the particle fraction of the components determined by wash extraction
• OPC-40701 – OPC UA for Surface Technology - Cleaning and Pretreatment
  7.8 STSysRinsingType ObjectType Definition
  Other Subtype of the 9:STSysType defined in OPC 40700 0:HasAddIn Object 3:Components 3:MachineComponentsType O Conformance Units STCleaningPretreatment STSysRinsingType Basic STCleaningPretreatment STSysRinsingType Identification STCleaningPretreatment STSysRinsingType Advanced Components ... used to assign components (e.g. of STCompType ) to the system. The components of the STSysRinsingType have additional subcomponents which are defined in Table 30 . Table 30 - STSysRinsingType Additional Subcomponents Source
• OPC-40701 – OPC UA for Surface Technology - Cleaning and Pretreatment
  7.9 STSysTreatmentType ObjectType Definition
  Other Subtype of the 9:STSysType defined in OPC 40700 0:HasAddIn Object 3:Components 3:MachineComponentsType O Conformance Units STCleaningPretreatment STSysTreatmentType Basic STCleaningPretreatment STSysTreatmentType Identification STCleaningPretreatment STSysTreatmentType Advanced Components ... used to assign components (e.g. of STCompType ) to the system. The components of the STSysTreatmentType have additional subcomponents which are defined in Table 32 . Table 32 - STSysTreatmentType Additional Subcomponents Source
• OPC-40702 – OPC UA for Surface Technology - Organic Coating Technology - Material Supply Systems
  7.2 STSysRamType ObjectType Definition
  VariableTypes for controlling and monitoring an overall ram system. It can contain several components as rams or vessels. The STSysRamType is formally defined in Table 19 . Table 19 - STSysRamType Definition ... Other Subtype of the 5:STSysType defined in OPC 40700 0:HasAddIn Object 4:Components 4:MachineComponentsType O Conformance Units MSS STSysRamType Basic MSS STSysRamType Components Components represent a collection
• OPC-40702 – OPC UA for Surface Technology - Organic Coating Technology - Material Supply Systems
  7.7 STSysVesselType ObjectType Definition
  parameters for controlling and monitoring a vessel of a material supply system. As the Components Object of the STSysVesselType is optional, a simple vessel without any additional components can also ... HasComponent Object 4:Monitoring 4:MonitoringType O 0:HasAddIn Object 4:Components 4:MachineComponentsType O 0:HasComponent Object 5:Description 0:FolderType O Conformance Units MSS STSysVesselType Basic MSS STSysVesselType
• OPC-40718 – OPC UA for Surface Technology - Shot Blasting Machinery
  6 Shot Blasting Technology Information Model overview
  structured in such a way that it represents the physical machine and its system components. The instantiation of the ShotBlastMachineType represents the entry point into the information model of each ... first level which help to structure the information model. These are the Components folder, in which the physical objects and system components of a shot blasting machine to be mapped
• OPC-40718 – OPC UA for Surface Technology - Shot Blasting Machinery
  7.1 ShotBlastMachineType ObjectType Definition
  HasAddIn Object 2:Identification 3:MachineIdentificationType M 0:HasAddIn Object 3:Components 3:MachineComponentsType M 0:HasComponent Object ShotBlastMedia ShotBlastMediaType O 0:HasComponent Object Monitoring 0:FolderType O 0:HasComponent ... shall also be referenced as AddIn in the MachineryBuildingBlocks Folder. Components is representing a collection of all physical components of the shot blast machine. ShotBlastingMedia is representing the material accelerated
• OPC-40718 – OPC UA for Surface Technology - Shot Blasting Machinery
  7.2 ShotBlastChamberType ObjectType Definition
  HasAddIn Object 2:Identification 3:MachineIdentificationType M 0:HasAddIn Object 3:Components 3:MachineComponentsType M 0:HasProperty Variable LoadingState 0:Boolean 0:PropertyType M 0:HasComponent Object 3:MachineryBuildingBlocks ... shall also be referenced as AddIn in the MachineryBuildingBlocks Folder. Components is representing a collection of all physical components of the shot blasting machine. Blaster is representing the device which
• OPC-40719 – OPC UA for Plasma Surface Technology
  6 Plasma Surface Technology Information Model overview
  structured in such a way that it represents the physical machine and its system components. The instantiation of the PlasmaSurfaceMachineType represents the entry point into the information model of each ... first level which help to structure the information model. These are the Components folder, in which the physical objects and system components of a plasma surface treatment machine
• OPC-40719 – OPC UA for Plasma Surface Technology
  7.1 PlasmaSurfaceMachineType ObjectType Definition
  HasAddIn Object 2:Identification 4:MachineIdentificationType M 0:HasAddIn Object 4:Components 4:MachineComponentsType M 0:HasComponent Object 4:Monitoring 4:MonitoringType M 0:HasAddIn Object 6:JobManagement 6:JobManagementType ... shall also be referenced as AddIn in the MachineryBuildingBlocks Folder. Components is representing a collection of all physical components of the plasma surface treatment machine. Monitoring is representing a collection
• OPC-40719 – OPC UA for Plasma Surface Technology
  7.2.1 Overview
  Node Class BrowseName DataType TypeDefinition Other Subtype of the PlasmaSurfaceMachineType 0:HasAddIn Object 4:Components 4:MachineComponentsType M 0:HasComponent Object 4:Monitoring 4:MonitoringType M Conformance Units PST LowPressurePlasmaSurfaceMachineType ... Basic PST LowPressurePlasmaSurfaceMachineType StateMachine PST LowPressurePlasmaSurfaceMachineType HeatingSystem PST LowPressurePlasmaSurfaceMachineType WorkpieceMotionDevice PST LowPressurePlasmaSurfaceMachineType Advanced The components of the LowPressurePlasmaSurfaceMachineType have additional subcomponents which are defined in Table 19 . Table 19 - LowPressurePlasmaSurfaceMachineType
• OPC-40719 – OPC UA for Plasma Surface Technology
  7.3.1 Overview
  Node Class BrowseName DataType TypeDefinition Other Subtype of the PlasmaSurfaceMachineType 0:HasAddIn Object 4:Components 4:MachineComponentsType M 0:HasComponent Object 4:Monitoring 4:MonitoringType M Conformance Units PST AtmosphericPressurePlasmaSurfaceMachineType ... Basic PST AtmosphericPressurePlasmaSurfaceMachineType StateMachine PST AtmosphericPressurePlasmaSurfaceMachineType Advanced The components of the AtmosphericPressurePlasmaSurfaceMachineType have additional subcomponents which are defined in Table 26 . Table 26 - AtmosphericPressurePlasmaSurfaceMachineType Additional Subcomponents Source Path Reference NodeClass
• OPC-40719 – OPC UA for Plasma Surface Technology
  7.5 PrecursorSystemType ObjectType Definition
  HasAddIn Object 2:Identification 4:MachineryComponentIdentificationType O 0:HasAddIn Object 4:Components 4:MachineComponentsType M 0:HasComponent Object 4:Monitoring 4:MonitoringType M 0:HasComponent Object 4:MachineryBuildingBlocks 0:FolderType ... shall also be referenced as AddIn in the MachineryBuildingBlocks Folder. Components is representing a collection of all physical components of the precursor system of a plasma surface treatment machine. Monitoring
• OPC-40719 – OPC UA for Plasma Surface Technology
  7.6 GasSystemType ObjectType Definition
  HasAddIn Object 2:Identification 4:MachineryComponentIdentificationType O 0:HasAddIn Object 4:Components 4:MachineComponentsType M 0:HasComponent Object 4:Monitoring 4:MonitoringType M 0:HasComponent Object 4:MachineryBuildingBlocks 0:FolderType ... Shall also be referenced as AddIn in the MachineryBuildingBlocks Folder. Components is representing a collection of all physical components of the gas system of a plasma surface treatment machine. Monitoring
• OPC-40719 – OPC UA for Plasma Surface Technology
  7.8.1 Overview
  HasAddIn Object 2:Identification 4:MachineryComponentIdentificationType O 0:HasAddIn Object 4:Components 4:MachineComponentsType M 0:HasComponent Object 4:Monitoring 4:MonitoringType M 0:HasComponent Object 4:MachineryBuildingBlocks 0:FolderType ... Shall also be referenced as AddIn in the MachineryBuildingBlocks Folder. Components is representing a collection of all physical components of the plasma surface treatment machine. Monitoring is representing a collection