Search

Scope: Core (OPC-10000-*) All specs

46 result(s) for Main Control System

OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

1 Scope

description of its components regarding a Compressed Air System. Main scope of this specification is the communication between the Main Control System and the higher-level manufacturing system(s). More
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

3.2.2 CASPart

Note 1 to entry: CASParts defined in this specification are: Airnet , all Components , Main Control System
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

3.2.4 Compressed Air System

Components and at least one Airnet , and is commonly equipped with one Main Control System
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

3.2.10 Integrated [Component]

Integrated [Component] A Component is Integrated if the Main Control System has control over the generation or treatment of compressed air. Note 1 to entry: A compressor is Integrated ... Main Control System has control over the loaded state. Note 2 to entry: The Main Control System can switch a Component between the two states Integrated and Isolated
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

3.2.11 Isolated [Component]

Isolated [Component] A Component is Isolated if the Main Control System has no control over the generation or treatment of compressed air. Note 1 to entry: A Component is Isolated ... Main Control System does not control the loaded state. Note 2 to entry: The Main Control System can switch a Component between the two states Integrated and Isolated
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

3.2.14 Quantity

measurements performed by a sensor, or calculations performed by a CASPart or the Main Control System to simulate a physical measurement. Note 1 to entry: A physical quantity ... integrated into the CASPart . Note 3 to entry: A calculation performed on the Main Control System which is used by a Component shall be assigned to that Component . EXAMPLE
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

3.2.16 Unavailable [Compressor]

compressor is Unavailable if it cannot be Integrated and controlled by the Main Control System . Note 1 to entry: The Main Control System cannot switch a compressor from Unavailable
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

4.1 Introduction to Compressed Air Systems

filters, air quality monitoring units etc., it is commonly also equipped with a Main Control System . The latter is used to control and/or monitor the connected devices and gather information ... Main Control System would be possible. The variety of Compressed Air System is rather wide. It could be e.g. two compressors and a Main Control System and a basic compressed
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

5 Use cases

cases Below is a list of possible use cases a Main Control System may implement fully or partly
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

5.1 Device Identification

management, e.g. Documentation Management, Energy Management and Maintenance Management. For this purpose, the Main Control System shall provide properties for asset identification. In addition to nameplate information of the CASParts
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

5.3 Maintenance Management

operator's maintenance management application, the Main Control System should provide Compressed Air System specific maintenance properties. To support asset monitoring, the Main Control System collects and analyzes operational ... wear). Since plant operators require a generalized health status of plant assets, the Main Control System shall provide a generalized Compressed Air System health status, based on the NAMUR NE107
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

5.4 Energy Management

integrate a Compressed Air System into the operator´s energy management, the Main Control System should provide energy-related information about the Compressed Air System and its installed CASParts ... able to trigger analyses of the Compressed Air Systems energy performance within the Main Control System
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

5.5 Operation

Control System ) the generation of compressed air. It should be possible to select from different operating modes for the Compressed Air System . For the operators / integrators process monitoring, the Main ... compressed air by accessing operational data of the Compressed Air System via the Main Control System . The Main Control System shall provide actual values of e.g. pressure, flow, inlet / outlet
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

6.3 Airnet Examples

connected to the red Airnet and treated as such. The Main Control System is not a part of the Airnet . Figure 8 - Simple Airnet Figure 9 shows a Compressed ... blue box are connected to the blue Airnet and treated as such. The Main Control System is not a part of any Airnet . Figure 9 - Two Simple Airnets Figure
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

6.4 Identification

Object of the CASIdentificationType which uses the Interface ITagNameplateType and its Properties . The Main Control System is identified by an Identification Object of the MachineryComponentIdentificationType. Components are identified ... System Charging system ChargingSystem ChargingSystems Compressor Compressor Compressor Compressors Condensate Drain Condensate drain CondensateDrain CondensateDrains Condensate Separator Condensate separator CondensateSeparator CondensateSeparators Converter Converter Converter Converters Cooling System Cooling system CoolingSystem
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.1 CASType ObjectType Definition

provides both Objects for Quantities and FunctionalGroups for its Airnets , Components , and the Main Control System . It is illustrated in Figure 16 and formally defined in Table 11 . Figure ... Compressed Air System . The optional Object MCS is the representation of the Main Control System . The InstanceDeclarations of the CASType have additional Attributes defined in Table 12 . Table 12 - CASType
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.6 MCSType ObjectType Definition

MCSType ObjectType DefinitionThe MCSType is the representation of a Main Control System and provides both Objects for Quantities and FunctionalGroups . It is illustrated in Figure 21 and formally defined ... Analyses provides Objects and Methods for analyses that can be invoked on the Main Control System . The optional FunctionalGroup Configuration provides Objects and Methods for configuring the behavior
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.25 AnalysisType ObjectType Definition

provides Objects and Methods that are used for invoking an analysis on the Main Control System and is formally defined in Table 53 . Table 53 - AnalysisType Definition Attribute Value BrowseName ... optional Object OutputFile shall contain the result of an analysis if the Main Control System can provide a file in the AddressSpace of the OPC UA Server . If not, this
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.25.1 Trigger

Trigger The Method Trigger is used to trigger an analysis on the Main Control System . The signature of this Method is specified below. There are no InputArguments or OutputArguments defined
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.26 AnalysesType ObjectType Definition

ObjectType Definition The AnalysesType provides O bjects for invoking analyses performed by the Main Control System and is formally defined in Table 56 . Such analyses may be performed on Compressed ... results of analyses performed by the manufacturer, automatically recurring analyses performed by the Main Control System , or other analyses that do not require a trigger and an output file
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.29 ConfigurationType ObjectType Definition

behavior of a CASPart . This specification defines configuration properties for Airnets and the Main Control System . There are no configuration properties defined for Components . It is formally defined in Table
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.30 AirnetConfigurationType ObjectType Definition

OperatingProfiles provides manufacturer or system specific operating profiles of an Airnet . On the Main Control System , operating profiles are stored as sets of parameters for parameterizing the behavior
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.31 MCSConfigurationType ObjectType Definition

display the ethernet communication settings of the OPC UA connection point of the Main Control System . The optional Object ConfigurationFile of the FileType shall be used to store the Main ... AddressSpace . This configuration file may be uploaded to or downloaded from the Main Control System using the described Methods. It should be a persistent representation of the currently active configuration
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.31.1 LoadConfigurationFile

LoadConfigurationFile is used to load the configuration file stored in ConfigurationFile into the Main Control System . The signature of this Method is specified below. There are no InputArguments or OutputArguments
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.31.2 SaveConfigurationFile

SaveConfigurationFile The Method SaveConfigurationFile is used to save the current configuration of the Main Control System to the file stored in ConfigurationFile. The signature of this Method is specified below
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.32 CommunicationSettingsType ObjectType Definition

CommunicationSettingsType ObjectType Definition The CommunicationSettingsType provides Variables for the communication settings of the Main Control System and is formally defined in Table 68 . Table 68 - CommunicationSettingsType Definition Attribute Value BrowseName
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.46 AirnetOperationalType ObjectType Definition

calculated by the OPC UA Server but may be calculated by the Main Control System . The definition of the KPIs is intentionally flexible so that the KPIs can be adapted
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

7.49.1 DrainTest

DrainTest is used to trigger a test of the condensate drain via the Main Control System . The signature of this Method is specified below. There are no InputArguments or OutputArguments
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

8.17 OperatingStateEnum

state machine does not imply the actual function or state machine in the Main Control System . It serves as an example of how the actual state machine may function. Figure
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

8.18 AirnetOperatingStateEnum

state machine does not imply the actual function or state machine in the Main Control System . It serves as an example of how the actual state machine may function. Figure
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

8.19 CompressorOperatingStateEnum

state machine does not imply the actual function or state machine in the Main Control System . It serves as an example of how the actual state machine may function. Figure
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

8.20 DryerOperatingStateEnum

state machines do not imply the actual functions or state machines in the Main Control System . It serves as an example of how the actual state machines may function. Figure
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.2 CAS Base Analyses Server Facet

Base Analyses Server Facet This Facet defines the elements for a Main Control System that provides prefabricated or pre-parameterized analyses on Compressed Air System or Airnet level. Although both
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.3 CAS Advanced Analyses Server Facet

Advanced Analyses Server Facet This Facet defines the elements for a Main Control System that provides parameterizable analyses on Compressed Air System or Airnet level and the possibility to store
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.4 CAS Base Configuration Server Facet

Base Configuration Server Facet This Facet defines the elements for a Main Control System that provides its OPC UA communication settings and the component class for Components . Table
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.5 CAS Advanced Configuration Server Facet

Advanced Configuration Server Facet This Facet defines the elements for a Main Control System whose configuration can be stored as a file in the OPC UA AddressSpace . Table
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.6 CAS Base Maintenance Management Server Facet

Base Maintenance Management Server Facet This Facet defines the elements for a Main Control System that provides a health state and statistics for CASParts . Table 168 - CAS Base Maintenance Management
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.7 CAS Advanced Maintenance Management Server Facet

Advanced Maintenance Management Server Facet This Facet defines the elements for a Main Control System that provides events and conditions. Table 169 - CAS Advanced Maintenance Management Server Facet Group Conformance
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.8 CAS Energy Management Server Facet

Energy Management Server Facet This Facet defines the elements for a Main Control System that provides necessary Variables and their historization for energy management applications. Table 170 - CAS Energy Management
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.9 CAS Operation Server Facet

Operation Server Facet This Facet defines the elements for a Main Control System that provides necessary Variables for operational applications. Table 171 - CAS Operation Server Facet Group Conformance Unit / Profile
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.10 CAS Base Server Profile

Base Server Profile This Profile defines the elements for a Main Control System that supports base functionality. Table 172 - CAS Base Server Profile Group Conformance Unit / Profile Title
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.11 CAS Advanced Server Profile

Advanced Server Profile This Profile defines the elements for a Main Control System that supports advanced functionality. Table 173 - CAS Advanced Server Profile Group Conformance Unit / Profile Title
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.12 CAS Maintenance Management Server Profile

Maintenance Management Server Profile This Profile defines the elements for a Main Control System that supports the maintenance management use case. Table 174 - CAS Maintenance Management Server Profile Group Conformance
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.13 CAS Energy Management Server Profile

Energy Management Server Profile This Profile defines the elements for a Main Control System that supports the energy management use case. Table 175 - CAS Energy Management Server Profile Group Conformance
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.14 CAS Dynamic Server Profile

Dynamic Server Profile This Profile defines the elements for a Main Control System that supports node manipulation during the runtime of the Server . Table 176 - CAS Dynamic Server Profile Group
OPC-40250-1 – OPC UA for Compressed Air Systems - Part 1: Main Control Systems

9.2.2.15 CAS Full Server Profile

Full Server Profile This Profile defines the elements for a Main Control System which supports all ConformanceUnits . Table 177 - CAS Full Server Profile Group Conformance Unit / Profile Title