The Duplex is an enumeration representing the configured, negotiated, or actual duplex mode of an Ethernet interface (see IEEE Std 802.3, 30.3.1.1.32, aDuplexStatus). The values of the Duplex Enumeration are defined in Table 18.
|
Name |
Value |
Description |
|
Full |
0 |
Full duplex. |
|
Half |
1 |
Half duplex. |
|
Unknown |
2 |
Link is currently disconnected or initializing. |
Its representation in the AddressSpace is defined in Table 19.
|
Attribute |
Value |
|||||
|
BrowseName |
Duplex |
|||||
|
IsAbstract |
False |
|||||
|
References |
NodeClass |
BrowseName |
DataType |
TypeDefinition |
Other |
|
|
Subtype of the Enumeration type defined in OPC 10000-5 |
||||||
|
HasProperty |
Variable |
EnumValues |
EnumValueType[] |
PropertyType |
|
|
|
Conformance Units |
||||||
|
BNM Ethernet Base Info |
||||||
The InterfaceAdminStatus is an enumeration for the possible desired states of the network interface (see IETF RFC 2863: The Interfaces Group MIB - ifAdminStatus). The values of the InterfaceAdminStatus Enumeration are defined in Table 20.
Table 20 – InterfaceAdminStatus Values
|
Name |
Value |
Description |
|
Up |
0 |
Ready to pass packets. |
|
Down |
1 |
Not ready to pass packets and not in some test mode. |
|
Testing |
2 |
In some test mode. |
Its representation in the AddressSpace is defined in Table 21.
Table 21 – InterfaceAdminStatus Definition
|
Attribute |
Value |
|||||
|
BrowseName |
InterfaceAdminStatus |
|||||
|
IsAbstract |
False |
|||||
|
References |
NodeClass |
BrowseName |
DataType |
TypeDefinition |
Other |
|
|
Subtype of the Enumeration type defined in OPC 10000-5 |
||||||
|
HasProperty |
Variable |
EnumValues |
EnumValueType[] |
PropertyType |
|
|
|
Conformance Units |
||||||
|
BNM Ethernet Base Info |
||||||
The InterfaceOperStatus is an enumeration for the possible operational states of the network interface (see IETF RFC 2863: The Interfaces Group MIB - ifOperStatus). The values of the InterfaceOperStatus Enumeration are defined in Table 22.
Table 22 – InterfaceOperStatus Values
|
Name |
Value |
Description |
|
Up |
0 |
Ready to pass packets. |
|
Down |
1 |
The interface does not pass any packets. |
|
Testing |
2 |
In some test mode. No operational packets can be passed. |
|
Unknown |
3 |
Status cannot be determined for some reason. |
|
Dormant |
4 |
Waiting for some external event. |
|
NotPresent |
5 |
Some component (typically hardware) is missing. |
|
LowerLayerDown |
6 |
Down due to state of lower-layer interface(s). |
Its representation in the AddressSpace is defined in Table 23.
Table 23 – InterfaceOperStatus Definition
|
Attribute |
Value |
|||||
|
BrowseName |
InterfaceOperStatus |
|||||
|
IsAbstract |
False |
|||||
|
References |
NodeClass |
BrowseName |
DataType |
TypeDefinition |
Other |
|
|
Subtype of the Enumeration type defined in OPC 10000-5 |
||||||
|
HasProperty |
Variable |
EnumValues |
EnumValueType[] |
PropertyType |
|
|
|
Conformance Units |
||||||
|
BNM Ethernet Base Info |
||||||
The NegotiationStatus is an enumeration representing the status of the auto-negotiation protocol (see IEEE Std 802.3, clause 30.6.1.1.4, aAutoNegAutoConfig). The values of the NegotiationStatus Enumeration are defined in Table 24.
Table 24 – NegotiationStatus Values
|
Name |
Value |
Description |
|
InProgress |
0 |
The auto-negotiation protocol is running and negotiation is currently in-progress. |
|
Complete |
1 |
The auto-negotiation protocol has completed successfully. |
|
Failed |
2 |
The auto-negotiation protocol has failed. |
|
Unknown |
3 |
The auto-negotiation status is not currently known, this could be because it is still negotiating or the protocol cannot run (e.g., if no medium is present). |
|
NoNegotiation |
4 |
No auto-negotiation is executed. The auto-negotiation function is either not supported on this interface or has not been enabled. |
Its representation in the AddressSpace is defined in Table 25.
Table 25 – NegotiationStatus Definition
|
Attribute |
Value |
|||||
|
BrowseName |
NegotiationStatus |
|||||
|
IsAbstract |
False |
|||||
|
References |
NodeClass |
BrowseName |
DataType |
TypeDefinition |
Other |
|
|
Subtype of the Enumeration type defined in OPC 10000-5 |
||||||
|
HasProperty |
Variable |
EnumValues |
EnumValueType[] |
PropertyType |
|
|
|
Conformance Units |
||||||
|
BNM AutoNeg |
||||||
The TsnFailureCode is an Enumeration to provide detailed error information for failures occurring during TSN stream establishment (see IEEE 802.1Qcc-2018, Table 46-15, TSN Failure Codes). The TsnFailureCode Enumeration is defined in Table 26.
Table 26 – TsnFailureCode values
|
Name |
Value |
Description |
|
NoFailure |
0 |
No failure |
|
InsufficientBandwidth |
1 |
Insufficient bandwidth |
|
InsufficientResources |
2 |
Insufficient bridge resources |
|
InsufficientTrafficClassBandwidth |
3 |
Insufficient bandwidth for Traffic Class |
|
StreamIdInUse |
4 |
StreamID in use by another Talker |
|
StreamDestinationAddressInUse |
5 |
Stream destination address already in use |
|
StreamPreemptedByHigherRank |
6 |
Stream pre-empted by higher rank |
|
LatencyHasChanged |
7 |
Reported latency has changed |
|
EgressPortNotAvbCapable |
8 |
Egress port is not AVBCapable |
|
UseDifferentDestinationAddress |
9 |
Use a different destination address |
|
OutOfMsrpResources |
10 |
Out of MSRP resources |
|
OutOfMmrpResources |
11 |
Out of MMRP resources |
|
CannotStoreDestinationAddress |
12 |
Cannot store destination address |
|
PriorityIsNotAnSrcClass |
13 |
Requested priority is not an SR Class priority |
|
MaxFrameSizeTooLarge |
14 |
MaxFrameSize is too large for media |
|
MaxFanInPortsLimitReached |
15 |
MaxFanInPorts limit has been reached |
|
FirstValueChangedForStreamId |
16 |
Changes in FirstValue for a registered StreamID |
|
VlanBlockedOnEgress |
17 |
VLAN is blocked on this egress port (Registration Forbidden) |
|
VlanTaggingDisabledOnEgress |
18 |
VLAN tagging is disabled on this egress port (untagged set) |
|
SrClassPriorityMismatch |
19 |
SR class priority mismatch |
|
FeatureNotPropagated |
20 |
Enhanced feature cannot be propagated to original Port |
|
MaxLatencyExceeded |
21 |
MaxLatency exceeded |
|
BridgeDoesNotProvideNetworkId |
22 |
Nearest Bridge cannot provide network identification for stream transformation |
|
StreamTransformNotSupported |
23 |
Stream transformation not supported |
|
StreamIdTypeNotSupported |
24 |
Stream identification type not supported for stream transformation |
|
FeatureNotSupported |
25 |
Enhanced feature cannot be supported without a CNC |
Its representation in the AddressSpace is defined in Table 27.
Table 27 – TsnFailureCode Definition
|
Attribute |
Value |
|||||
|
BrowseName |
TsnFailureCode |
|||||
|
IsAbstract |
False |
|||||
|
References |
NodeClass |
BrowseName |
DataType |
TypeDefinition |
Other |
|
|
Subtype of the Enumeration type defined in OPC 10000-5 |
||||||
|
HasProperty |
Variable |
EnumValues |
EnumValueType[] |
PropertyType |
|
|
|
Conformance Units |
||||||
|
BNM TSN Base Info |
||||||
The TsnStreamState is an enumeration representing the state of the configuration process of a TSN Talker or Listener.
The default value is Disabled. The TsnStreamState Enumeration is defined in Table 28.
Table 28 – TsnStreamState Values
Its representation in the AddressSpace is defined in Table 29.
Table 29 – TsnStreamState Definition
|
Attribute |
Value |
|||||
|
BrowseName |
TsnStreamState |
|||||
|
IsAbstract |
False |
|||||
|
References |
NodeClass |
BrowseName |
DataType |
TypeDefinition |
Other |
|
|
Subtype of the Enumeration type defined in OPC 10000-5 |
||||||
|
HasProperty |
Variable |
EnumValues |
EnumValueType[] |
PropertyType |
|
|
|
Conformance Units |
||||||
|
BNM TSN Base Info |
||||||
The TsnTalkerStatus is an enumeration representing the state of the TSN Talker configuration.
The default value is None. The TsnTalkerStatus Enumeration is defined in Table 28.
Table 30 – TsnTalkerStatus Values
|
Name |
Value |
Description |
|
None |
0 |
No Talker detected. |
|
Ready |
1 |
Talker ready (configured). |
|
Failed |
2 |
Talker failed. |
Its representation in the AddressSpace is defined in Table 29.
Table 31 – TsnTalkerStatus Definition
|
Attribute |
Value |
|||||
|
BrowseName |
TsnTalkerStatus |
|||||
|
IsAbstract |
False |
|||||
|
References |
NodeClass |
BrowseName |
DataType |
TypeDefinition |
Other |
|
|
Subtype of the Enumeration type defined in OPC 10000-5 |
||||||
|
HasProperty |
Variable |
EnumValues |
EnumValueType[] |
PropertyType |
|
|
|
Conformance Units |
||||||
|
BNM TSN Base Info |
||||||
The TsnListenerStatus is an enumeration representing the state of the TSN Listener configuration.
The default value is None. The TsnListenerStatus Enumeration is defined in Table 28.
Table 32 – TsnListenerStatus Values
|
Name |
Value |
Description |
|
None |
0 |
No Listener detected. |
|
Ready |
1 |
Listener ready (configured). |
|
PartialFailed |
2 |
One or more Listeners ready, and one or more Listeners failed. |
|
Failed |
3 |
Listener failed. |
Its representation in the AddressSpace is defined in Table 29.
Table 33 – TsnListenerStatus Definition
|
Attribute |
Value |
|||||
|
BrowseName |
TsnListenerStatus |
|||||
|
IsAbstract |
False |
|||||
|
References |
NodeClass |
BrowseName |
DataType |
TypeDefinition |
Other |
|
|
Subtype of the Enumeration type defined in OPC 10000-5 |
||||||
|
HasProperty |
Variable |
EnumValues |
EnumValueType[] |
PropertyType |
|
|
|
Conformance Units |
||||||
|
BNM TSN Base Info |
||||||